Multi-function LED Solar Wall Light
3 working modes-
1. PIR sensor + dim light mode
2. PIR sensor automatic mode
3. Constant Light mode
LED Features:
1. High efficiency, low energy consumption
2. Automatic delay and repair in the dark
3. Waterproof, heat-resistant
4. Charge for 6 hours of continuous lighting for one day
5. The use of low cost, long life, no maintenance costs
6. Installation is simple and convenient
7. Adequate brightness , energy saving and enviromental protection
8. Light quality, the spectrum is not ultraviolet and infrared, energy is small ,
no radiation exposure to UV radiation will not be hurt, is a typical green light source
9. Green , lamp waste recylable, no pollution, mercury-free ingredients
This product is suitable for corridors, gardens ,gates, rooftops, garden walls and other outdoor enviroment.
Product advantages:
1. Installation is simple (only use 2 screws to fix the product in the outdoor sun-ray wall can be), easy to use.
2. New environmental components materials, fire-class steel PC, aviation-grade aluminum anode sandblasting.
3. Environmental lithium battery, long life (average life expectancy of more than 5 years, the battery can be replaced, cost only ¥0.005 per day).
4. High-power high-brightness LED * 21, no light failure, no flash frequency, no radiation.
5. Intelligent light-sensing control, no adjustment, energy-saving and convenient.
6. Use a long time, full of electricity, sustainable lighting about 40 hours.
Product parameters:
Solar panel | 5V/2W Polycrystalline Silicon |
Lithium battery | Lithium 18650 2600mAh /3.7V |
LED: power | 21pcs*2835#0.2W LED |
Light control sensor | Auto-light at light |
Charging time | 8 hours |
Working Time | 10-12 hours |
Intelligent machine power | <0.05mA |
Color Temperature | 6000-7000K |
Lumens | 200LM,150/20LM,30LM |
Material | ABS,PS, Stainless Steel |
Specifications(mm) | 164*109*84mm |
Packing Size(cm) | 16.8*11.3*8.8cm |
QTY/CTN(PCS) | 30 |
N.W./G.W(kg) | 9.6kg/10kg |
Working voltage | 3.7V |
This product is energy saving motion activated solar wall light.
By using solar power and Lithium battery technology.
This solar light is widely used for entrance, corridors, passages, countyard, stainways, garages etc.
It is easy to set up and no wire needed.
During the day, the solar panel fitted on top of each light will change the battery inside.
At dusk, the 21 LEDs will activate automatically using the stored energy from the sun.
The PIR (Passive Infrared) technology will enable the LEDs to turn to maximum brightness
(250-330 Lumen) when motion is detected. It brings a lot safety, security and convenience for your
home and garden.
Function:
1. This product has a light sensor, it turns ON and OFF automatically everyday.
While the surrounding light is over 100 LUX, the product begiins to change by itself.
While the surrounding light is below 100-10 lux, the light turns on automatically.
2. Multi-function, this product has 3 mode, press and release the switch once to change
the mode in turn.
Three indicator lights correspond to 3 working mode (eg. Fig 1):
(1) Green indicator light turns on: Motion Sensor plus Dim Light Mode. Dim light (about 20LM) is always on through out the night.
While people come close to the light, motion sensor is triggered and become very bright (250LM) and last upto 37 seconds, and
then turn to dim light. Motion triggers maximum 160 times every night.
(2) Blue indicator light turns on: Motion Sensor Mode. When people come close to the light, it turns on very brigt gradually (about 330LM) and last 37 seconds. Without motion, the light turn off.
(3) Red indicator light turns on: Always on Mode, Strong light (about 80LM) for the first 5 hours, dim light (about 40LM) for the next 5 hours.
Installation (Fig 3)
1. Choose the desired place, drill 3 holes as per the dimension of the above picture (Fig 3). Put the plastic anchors in.
2. First insert the screw into the wall and leave the screw 5-8mm to projuct from the surface. Fix the light to the surface by
hooking the keyhole 1 at the back cover over the mounted screw.
3. Then mount the screws 2 and 3 from the front.
Battery replacement (Fig 4)
1. Take down the product, remove the 4pcs 3.8mm grub screw at the back cover of the product.
2. Remove the 4pcs screws (roung-headed screw 3.8mm) at the front of the product.
3. Replace the Lithium 18650 battery according to the marks on the product indicating the polarities of the battery.
Attention:
1. After replaced the battery, please put the product under direct sunlight to activate the product before use it normally.
2. Dispose the used battery properly! DO NOT DISPOSE THE BATTERY IN FIRE!
Mainenance and Attention:
1. Before use the solar light for the first time, leave the light under direct sunlight for about 36-48 hours,
The light will achieve optinum light output after the enomous exposure to the sunlight.
2. Please keep the surface of the solar panel clean, to make sure the product works at its best performance.
3. It is important to install the light in a location that receive full sunlight each day, away from the shade caused by trees, buildings etc. Shady locations will not allow the battery to be fully changed and will reduce the hours of night time light.
4. This solar light include a built-in photo sensor, which detects the level of surrounding natural light and controls when the light will automatically switch on and off. The solar light should be placed at lease 2 meters apart from one another and away from other night time lights sources as this might keep the solar lights from automatically turning on at dusk.
5. The performance of the solar light is depended on the geographical location, weather conditions and seasonal sunlight availability.
On cloudy days and during winterm the solar light will not receive as much direct sunlight, resulting in reduced brightness
and reduced operation time.